5J8200 Seal U Cup 1672304 2892946 1672310 5J8238 5J8325 5J8400 5J8275 5J8350 For

5J8200 Seal U Cup 1672304 2892946 1672310 5J8238 5J8325 5J8400 5J8275 5J8350 for

1672310 - Seal-U-Cup 5J8238 fits ()
FIRST PRICE PARTS

ARTICULATED TRUCK D250B D250E D25D D300B D300E D350E D400E D40D
BACKHOE 931
BACKHOE LOADER 416B 416C 426 426B 426C 428 428B 428C 436C 438B 438C 446 446B
BULLDOZER 3S 4S 814S
CHALLENGER 65 65C 75 75C 75D 85C
COMPACT WHEEL LOADER 910
EXCAVATOR 215 215B 215C 215D 225 245
FORWARDER 554 574
FRONT SHOVEL 5080
INTEGRATED TOOLCARRIER IT12 IT12B IT18B IT18F IT24F IT28F
LANDFILL COMPACTOR 826B
MOTOR GRADER 120H 12G 12H 12H NA 130G 140G 140H 140H NA 14G 160G 16G
PIPELAYER 561C 561D
RECLAIMER MIXER RM-350B
SOIL COMPACTOR 815 815B 825C
STABILIZER MIXER SM-350
TRACK LOADER 931B 931C 931C II 935C 939 941 943 951B 953 953C 963 973
TRACK SKIDDER D4HTSK II D5HTSK II
TRACK-TYPE TRACTOR D3B D3C II D4E D4E SR D4H D4H XL D5C III D5H D5H XL D5M D5N D6M
TRACTOR 768C
WHEEL DOZER 814 814B
WHEEL HARVESTER 550 570 580
WHEEL LOADER 920 930 930R 950 966C 966D 966F 966F II 966G 966G II 970F 972G 972G II
WHEEL SCRAPER 613 613C
WHEEL SKIDDER 515 518 518C 525 528
WHEEL TRACTOR 613B 613C

Removal Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publiion, NENG2500, "Dealer Service Tool alog" for tools and supplies suitable to collect and contain fluids on products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03032896
Disconnect harness assembly (1) and remove fuel pressure sensor (2). (1) Fuel pressure sensor ... 10 2 N m (89 18 lb in)Installation Procedure
Install fuel pressure sensor (2) in the reverse order of removal.
Tighten fuel pressure sensor (2) to a torque of 10 2 N m (89 18 lb in).

Improper jump start cable connections can cause an explosion resulting in personal injury.Prevent sparks near the batteries. Sparks could cause vapors to explode. Do not allow jump start cable ends to contact each other or the engine.
If the installation is not equipped with a backup battery system, it may be necessary to start the engine from an external electrical source.First, determine the reason that it is necessary to start with power from an external source.Many batteries which are considered unusable are still rechargeable. After jump starting, the alternator may not be able to fully recharge batteries that are severely discharged. The batteries must be charged to the proper voltage with a battery charger. For information on testing and charging, refer to the Special Instruction, SEHS7633, "Battery Test Procedure".
Using a battery source with the same voltage as the electric starting motor. Use ONLY equal voltage for jump starting. The use of higher voltage will damage the electrical system.Do not reverse the battery cables. The alternator can be damaged. Attach ground cable last and remove first.When using an external electrical source to start the engine, turn the generator set control switch to the "OFF" position. Turn all electrical accessories OFF before attaching the jump start cables.Ensure that the main power switch is in the OFF position before attaching the jump start cables to the engine being started.
Turn the start switch on the stalled engine to the OFF position. Turn off all accessories.
Connect one positive end of the jump start cable to the positive cable terminal of the discharged battery. Connect the other positive end of the jump start cable to the positive cable terminal of the electrical source.
Connect one negative end of the jump start cable to the negative cable terminal of the electrical source. Connect the other negative end of the jump start cable to the engine block or to the chassis ground. This procedure helps to prevent potential sparks from igniting combustible gases that are produced by some batteries.
Charge the batteries. The engine will not continue to run after starting if the batteries have not been charged.
Start the engine.
Immediately after the stalled engine is started, disconnect the jump start cables in reverse order.