7K9205 7K9203 7K9201 Dust Wiper Seals Set For 980G 980H 966H

7K9205 7K9203 7K9201 Set of 6 Seal Dust Fits 980G 980H 966H

Reliable Aftermarket Parts Our Name Says It All Set of Six (6) New Aftermarket Replacement Link Pin Seals || Fits Models: 980G, 980H, 966H || Lip-Type Seal, || Rod is 2.5" || Replaces Part Numbers: 7K9205, 7K-9205

BACKHOE LOADER 422E 424B 424B HD 424D 428 428B 428C 428D 428E 432D 432E 434E 438 438B 438C 438D 442D 442E 444E
CHALLENGER 65 65C 75
COMPACT WHEEL LOADER 914G

Seal for New 7K9203 7K-9203 5P0093 5P-0093 3046, 3054, Ships Free!!!
FIRST PRICE PARTS

EXCAVATOR 215 225 322B L 322C FM 324D FM LL 325B L 325D FM 325D FM LL 330B L 330D FM 568 FM LL
GRAPPLE-LOG LOADING GH52 GLC85 GLL60
INTEGRATED TOOLCARRIER IT14G2 IT18 IT18B IT28G IT38F IT38G IT38G II IT38H IT62G IT62G II IT62H
MOTOR GRADER 120M 120M 2 12M 12M 2 12M 3 12M 3 AWD 140M 140M 2 140M 3 140M 3 AWD 14G 160M 160M 2 160M 3 160M 3 AWD 24H 24M
TRACK LOADER 941 943 951B 953 953C 953D 963 973 973C 973D 977K 977L 983
TRACK SKIDDER 517 527 D4HTSK II D4HTSK III D5HTSK II
TRACK-TYPE TRACTOR D4H D4H XL D5H D5H XL D5M D5N D5R LGP D6H D6H II D6H XL D6H XR D6M D6N D6N LGP D6N OEM D6R D6R II D6R STD D6T D6T LGP D6T LGPPAT
WHEEL LOADER 916 918F 920 924F 924G 924GZ 924H 924HZ 926 926A 928F 928G 928H 928HZ 930 930K 936 936F 938F 938G 938G II 938H 950 950 GC 950B 950B/950E 950F 950F II 950G 950G II 950H 950K 960F 962G 962G II 962H 962K 966C 966D 966F 966F II 966G 966G II 966H 966K 966M 966M XE 966R 970F 972G 972G II 972H 972K 972M 972M XE 980B 988 G936
WHEEL SKIDDER 518 530B 535B 545

The timing (crank) gear - now included on all Remanufactured Crankshafts.
Warranty same as new - six months unlimited miles/hours.
Core acceptance - simple with most cores acceptable for full credit, the core must be:
... One piece genuine forging with crank gear.
... Not visibly cracked.
... Not gouged or grooved in the fillet area because of contact with the connecting rod, cylinder block, or main bearing cap.
... Not damaged from improper storage or handling.
... Not pitted on the thrust face, taper or gear diameter1.
... Not chromed or welded1.

You must read and understand the warnings and instructions contained in the Safety section of this manual before performing any operation or maintenance procedures.Valve Lash-3306B Engine
Check/Adjust
Initial valve lash adjustment is recommended at the first oil change interval due to initial wear and seating of valve train components.Subsequent valve lash adjustments should be made Every 2000 Hours.This maintenance is recommended by as part of a lubriion and preventive maintenance schedule to provide maximum engine life.
Operation of engines with improper valve adjustments will reduce engine efficiency. This reduced efficiency could result in excessive fuel usage and/or shortened engine component life.Only qualified service personnel should perform this maintenance. Refer to the Service Manual or your dealer for the complete valve lash adjustment procedure.
Be sure the engine cannot be started while this maintenance is being performed. To prevent possible injury, do not use the starting motor to turn the flywheel.Hot engine components can cause burns. Allow additional time for the engine to cool before measuring/adjusting valve lash clearance.
Measure the valve lash with the engine stopped. In order to obtain an accurate measurement, the allow the valves to cool before performing this maintenance. Valve Rotators
When inspecting the valve rotators, protective glasses or face shield and protective clothing must be worn, to prevent being burned by hot oil or spray.
If a damaged rotator is not replaced, valve face guttering could result in pieces of the valve to fall into the cylinder. This can cause piston and cylinder head damage.
After setting the valve lash and before installing the valve covers:1. Start the engine. Follow the engine starting procedure in this manual. Operate the engine at low idle.2. Observe the top surface of each valve rotator. Each valve rotator should turn slightly each time the valve closes.If a valve fails to rotate, contact your dealer.Fuel Ratio Control, Set Point, and Low Idle-3306B Engine

The charts list the Remanufactured Crankshafts available and the acceptable forging numbers for Remanufactured Crankshafts. Make sure the service part number shown fits your appliion. For more information about Remanufactured Crankshafts, see (IRM), REM85-18.
1Chromed, welded, or pitted cores can be returned for partial credit on upgrade to new crankshafts (not undersize).