DX225 DH225 Arm Boom Bucket Cylinder Seal Kit Control Valve Seal Kit Center Join Seal Kit

DX225 DH225 Arm Boom Bucket Cylinder Seal Kit Control Valve Seal Kit Center Join Seal Kit

SEAL KITS---
BOOM CYL SEAL KIT . ARM CYL SEAL KIT . BUCKET CYL SEAL KIT
MAIN PUMP SEAL KIT . HYDRAULIC PUMP SEAL KIT . PIOLVE VALVE SEAL KIT.
GEAR PUMP SEAL KIT VALVE SEAL KIT .PUMP PLUNGE SEAL KIT .
.CONTROL VALVE SEAL KIT. SWING MOTOR SEAL KIT .. TRAVEL MOTOR SEAL KIT .
ADJ CYL SEAL KIT. CENTER JIONT KIT BREAKER SEAL KIT

Oil Seal -- TC TB TCV TCN DB DC DCY TC4Y ISPID BABSL

Piston seal : SPGW SPGO SPG SPGA NCF ODI OSI OUIS OHM OKH DAS , OK SELA OUY D-8

Rod Seal : IDI IUH ISI IUIS D-2 D-3 D-6
　
U Seal : UPI UPH USH USI V99F V96H UN

Buff Seal : HBTS HBY HBTTS D-14

Wiper Seal : DKB DKBI DKBI3 DKBZ DKI , DWI DKH DWIR DSI LBI LBH VAY DH ME-2 ME-8

Wearing Ring : WR KZT RYT

　
Rotary Seal : ROI D-14 SPN

Back Up Ring : N4W BRT-PTFE BRT-NYLON BRT2 BRT3 BRT-G BRT-P BRN2 BRN3

O Ring : Oring Kit P series G series AS series S series M 1.5 series M 2.0 series M 1.9series M 2.4 series

M 3.0 series M4.0 series

Piston seal : SPGW SPGO SPG SPGA NCF ODI OSI OUIS OHM OKH DAS , OK SELA OUY D-8

Rod Seal : IDI IUH ISI IUIS D-2 D-3 D-6

Valve Pusher Floating oil seal Bushing hydraulic cylinder seals cylinder seal kits

Table 2
Specifiion for 274-1953 Cylinder Head Gp and 235-2974 Cylinder Head Gp
Item Qty Part Specifiion Description
A - - Cylinder head thickness:
Thickness of a new cylinder head is 120.00 0.15 mm (4.724 0.006 inch)
Minimum thickness of a used cylinder head is 119.50 mm (4.705 inch)
Illustration 3 g02548907
(1) Sleeve bearing joint
(2) Oil gallery
(3) Oil holes
(4) Sleeve bearing
Camshaft bearings must be installed into their correct position. Failure to do so will result in engine damage.
Illustration 4 g02548916
Table 3
Specifiion for 274-1953 Cylinder Head Gp and 235-2974 Cylinder Head Gp
Item Qty Part Specifiion Description
B - - Orientation of the sleeve bearing joint is 20 5 degrees above horizontal
C - - Bore for camshaft sleeve bearing is 90.985 0.020 mm (3.5821 0.0008 inch)
Illustration 5 g02548921
Table 4
Specifiion for 274-1953 Cylinder Head Gp and 235-2974 Cylinder Head Gp
Item Qty Part Specifiion Description
4 7 216-5582 Bushing The depth of installation of the sleeve bearings is important. Install sleeve bearings to the following depths:
Dimension (D): 8.0 0.5 mm (0.31 0.02 inch)
Dimension (E): 178.1 0.5 mm (7.01 0.02 inch)
Dimension (F): 349.5 0.5 mm (13.76 0.02 inch)
Dimension (G): 521.0 0.5 mm (20.51 0.02 inch)
Dimension (H): 692.4 0.5 mm (27.26 0.02