2366368 2316844 1764999 1997417 2254625 LODER KIT ARM BOOM BUCKET SEAL

2366368 2316844 1764999 1997417 2254625 LODER KIT ARM BOOM BUCKET SEAL

Kit  - 2366368 Aftermarket Hydraulic Cylinder Seal Kit
Kit King USA 85 mm Rod & 120 mm Bore || Equipment Types: Excavators, Material Handlers || Compatible Equipment Models: 318C, 319C, 319D, 319D L, 319D LN, 320B, 320B L, 320C, 320C L, 320C LN, 320C LRR, 320C S, 325D L, 329D L, 330C, 330C L, 345B, 345B L, 345B LC, M322C, M322D and More || Typical Hydraulic Appliions: Boom, Bucket || Fits Cylinder Models: 1589058, 1839004, 2590859, 2836132, 2898154, 2963253, 3021735, 3676473, 3683242 and More

For Excavator 330D Arm Cylinder Seal Kit 2590768 2316845 2316844
NC Part Number: 2590768 || Appliions:For Excavator 330D Arm Cylinder

Hydraulic Seal Kit 1997417 fits 325B L 328D LCR 330B 330B L 345B L

225-4625 Bucket Cylinder Seal KIT Applicable to Excavator E330D AFTERMARKET Replacement 2254625
MOTTROL PART NO.: 225-4625, 2254625, APPLIION MODEL: E330D (CYLINDER PART NO.: 129-7832, ROD 130 & BORE 190) || QUALITY: WEARABLE, HIGH TEMPREATURE ENDURANCE, HIGH PRESSURE RESISTANCE, GOOD PERFORMANCE || MATERIAL: NITRILE RUBBER(NBR), POLYTETRAFLUOROETHYLENE(PTFE), POLYURETHANE (PU), NYLON, COPPER, STEEL ETC || THE SEAL KIT CONSISTS OF ROD SEAL (IDI/ISI), BUFFER RING (HBY), DUST SEAL (DKB), O-RING, BACK UP RING, PISTON SEAL (SPGO/SPGW/SPG/KDAS), WEAR RING (WR/KZT/N4W)ETC; VARIOUS SEAL KITS AVAILABLE FOR BOOM/ARM/BUCKET HYDRAULIC CYLINDER, MAIN PUMP, CONTROL VALVE, TRACK ADJUSTER, SWING MOTOR, TRAVEL MOTOR, CENTER JOINT, REGULATOR VALVE, PILOT VALVE AND GEAR PUMP, ALSO O-RING BOX, COUPLING, DU BUSHING, PISTON STEEL RING, PUSHER ARE AVAILABLE || NOTE: THE PICTURE IS JUST FOR REFERENCE, THE REAL PRODUCTS MAY LOOK DIFFERENT

Check the fuel pressure before the gas pressure regulator and after the gas pressure regulator. Table 1 lists the fuel pressure that is required for the gas pressure regulator.
Table 1
Requirements for Fuel Pressure To the Gas Pressure Regulator
Fuel System Pressure
Low-pressure gas
Naturally Aspirated 10.3 to 34 2 kPa (1.50 to 5 0.25 psi)
High-pressure gas 172 to 207 7 kPa (25 to 30 1 psi) Pressure of the Fuel Supply To the Carburetor
The gas pressure regulator maintains a pressure differential between the air and the fuel that is supplied to the carburetor. After setting, the gas pressure regulator will maintain the pressure differential in response to changes in the air pressure.Use a water manometer for measuring the pressure differential. Obtain the measurement when the engine is operating at high idle rpm. After a load is applied, the fuel pressure will usually decrease by approximately -.1 kPa (0.40 inch of H2O) to -.25 kPa (1.00 inch of H2O). If the performance of the gas pressure regulator is erratic, the gas pressure regulator may require service.Natural Gas
Set the pressure of the fuel supply to a maximum of 1 kPa (4.01 inch of H2O) to 1.2 kPa (4.82 inch of H2O) HIGHER than the ambient air pressure.Propane
Set the pressure of the fuel supply to −0.37 −0.06 kPa (−1.5 0.250 inches of H2O) LOWER than the ambient air pressure.Note: If the engine is equipped with a vaporizer/regulator for liquid propane fuel supply, the vaporizer/regulator will regulate the fuel supply pressure at the correct level. No adjustment is required.